Flat Rate Shop Manual
Version 1.0
Note: the services and/or procedures in this book do not include the cost of any parts unless specifically stated!
We are not responsible for any typos, mistakes or omissions within this manual.
This manual is to be used as a reference only as actual job/task time may vary depending upon unforeseen circumstances that can arise due to the overall condition of the customer’s firearm which many times is unknown until the firearm is disassembled and inspected.
Re-Bluing/Refinishing after procedures is additional cost on all Guns ("IF" required)
Shop Labor Rate for Gunsmithing is $75.00 per hour and we bill in 15 minute increments (0.25 hrs).
Shop Labor Rate for Machining is $115.00 per hour to include set-up time, also billed in 15 minute increments.
A $2.00 fee for shop miscellaneous shop materials (cleaning supplies, lubricants, rags etc.) will be added to each Invoice to cover the cost of shop incidentals.
A $75.00 LOADED GUN FEE will be added to any bill in which the customer brings a loaded firearm into the shop for repair without prior warning!! This includes any firearm shipped to the shop for repair! Customer neglect has driven this as I have almost been shot twice now!
The Gun Surgeon
4124 Millerstown Road, Urbana, OH 43078
937-206-8744
Service or Procedure Time/Hrs.
Does Not Include parts or materials
Metal Finishing
Handgun Parts/Small Parts
High Polish --------------------------------------------------------------------------------------------------- Sent out in most cases
Satin Finish -------------------------------------------------------------------------------------------------- Sent out in most cases
Long Guns
High Polish -------------------------------------------------------------------------------------------------- Sent out in most cases
Satin Finish --------------------------------------------------------------------------------------------------- Sent out in most cases
Engine Tune Small Parts ---------------------------------------------------------------------------------- 0.5 – 1.0
Draw-Filing (Hourly Rate) ------------------------------------------------------------------------------------------ $75 per hr.
Metal Checkering (Hourly Rate) ---------------------------------------------------------------------------------- $75 per hr.
Faux Color Case Color Restoration
Does not include polishing time
Small Parts (all small parts in a single gun) -------------------------------------------------------------------- Min Time 0.5
Actions (Does not include fixturing if required) ---------------------------------------------------------------- Min Time 1.0
Actions (Includes Fixturing) --------------------------------------------------------------------------------------- Min Time 1.5
Muzzle Loader Work
Pull Ball ----------------------------------------------------------------------------------------------------------------- 0.5 – 1.5
Remove Broken Ramrod from Barrel --------------------------------------------------------------------------- 0.5 – 1.5
Repair/Adjust Trigger (s) ------------------------------------------------------------------------------------------- 1.5 – 3.0
Repair/Replace Lock Parts/Frizzen, Hammer ----------------------------------------------------------------- 1.5 – 3.0
Repair/Replace Lock Spring --------------------------------------------------------------------------------------- 0.5 – 1.5
Bend Hammer to Clear Scope ------------------------------------------------------------------------------------ 0.5
Handgun Work/Revolver
Chamfer/Throat/Face Revolver Barrel ------------------------------------------------------------------------- 1.0
Chamber Revolver Cylinder
Open Existing Holes ------------------------------------------------------------------------------------------------- 1.0
Blank Cylinder -------------------------------------------------------------------------------------------------------- 1.0
DA Revolver Action Job – Smooth/Tune Action
Smith & Wesson ----------------------------------------------------------------------------------------------------- .75 – 2.0
Colt ---------------------------------------------------------------------------------------------------------------------- 1.5 – 3.5
Bevel Cylinder Face -------------------------------------------------------------------------------------------------- 0.75
Chamfer Charge Holes ---------------------------------------------------------------------------------------------- 0.5 – 0.75
Set Back Barrel/Reset B/C Gap
Colt ---------------------------------------------------------------------------------------------------------------------- 0.75
Smith & Wesson ----------------------------------------------------------------------------------------------------- 1.5
SA Revolver Action Job/Tune Action -------------------------------------------------------------------------- 1.5 – 3.0
Time Cylinder -------------------------------------------------------------------------------------------------------- 0.5 – 1.5
Range Barrel to Cylinder ------------------------------------------------------------------------------------------- 0.75 – 2.0
Re-barrel Revolver (Remove Old Barrel, Replace with Factory New Barrel, Labor Only) ---------- 1.0 – 2.0
Line Bore Cylinder to Barrel -------------------------------------------------------------------------------------- 2.0
Fit Single Action Cylinder Stop/Bolt for Cowboy Action Fast Draw -------------------------------------- 1.0
Straighten Crane on Revolver ------------------------------------------------------------------------------------- 0.5
Install Crane Lock ---------------------------------------------------------------------------------------------------- 1.0
Remove/Modify Revolver Hammer Spur ---------------------------------------------------------------------- 0.5 – 1.0
Convert Revolver from Square Butt to Round Butt (Bluing Additional) -------------------------------- 0.5 – 1.0
Fit Brass/Steel Grip Frame to Colt or Ruger Single Action ------------------------------------------------ 1.0
Fit After Market Grip Panels to Colt or Ruger Single Action (assumes Panel is not undersized) -- 1.0
Scope Work
Drill & Tap for Scope Mounts ------------------------------------------------------------------------------------- $50 first hole $25 ea. thereafter
Install Colored Front Sight Inserts ------------------------------------------------------------------------------- 0.75
Handgun Work/Auto Pistols
Bluing/Refinishing ("IF" required) after procedures additional on all Guns
Semi-Auto Action Smooth & Tune (Does Not Include any Parts) ------------------------------------ 1.0 – 4.5
Simple Blow-Back Type Pistols --------------------------------------------------------------------------------- 1.0 – 2.5
1911 Style ----------------------------------------------------------------------------------------------------------- 2.0 – 3.5
Stryker Fired Double Action Pistols ---------------------------------------------------------------------------- 1.5 – 2.0
External Hammer Fired Double Action Pistols --------------------------------------------------------------- 2.5 – 4.5
Tighten 1911 Slide ------------------------------------------------------------------------------------------------ 1.0 – 1.5
Fit “Gunsmith” Barrel to 1911 Auto, Not Including Barrel
Non-ramped Barrel ----------------------------------------------------------------------------------------------- 1.75
Ramped Barrel ----------------------------------------------------------------------------------------------------- 2.5
Fit “Drop-in” Barrel to 1911 Auto, Not Including Barrel
Non-ramped Barrel ----------------------------------------------------------------------------------------------- 0.5 – 1.0
Fit and Install Barrel Bushing on 1911 Auto (does not include cost of Bushing) ----------------- 0.5 – 0.75
Bevel Magazine Well of 1911 Auto (does not include cost of refinishing)
No Additional Charge for Cold Bluing --------------------------------------------- ---------------------------- 1.0
Install and Blend Smith & Alexander Mag Well ---------------------------------------------------------- 1.0
Weld on Mag Well Funnel on 1911 Auto (Brown, Extreme)
Does not include cost of refinishing, no additional charge for cold bluing ------------------------------ 1.5
Stipple Front Strap ---------------------------------------------------------------------------------------------- 1.5
Open and Flare Ejection Port of 1911 Auto Slide ------------------------------------------------------- 0.75
Throat, Polish Barrel and Feed Ramp of 1911 Auto ---------------------------------------------------- 1.0
Smooth and Polish Bolt Face --------------------------------------------------------------------------------- 0.5
Fit New 1911 Trigger (Does not Include the cost of the Trigger) ---------------------------------------- 0.25
Fit Custom Hammer to 1911 (does not include the cost of the hammer) ----------------------------- 0.25 – 1.0
Trigger Job on 1911
Does Not Include the Cost of Any Parts
4 Pound + Pull Weight -------------------------------------------------------------------------------------------- 1.0 – 1.5
3 – 4 Pound Pull Weight ------------------------------------------------------------------------------------------ 2.0
2 – 3 Pound Pull Weight ------------------------------------------------------------------------------------------ 3.0
Install Spring Kit ---------------------------------------------------------------------------------------------------- 0.75
Cut Front Cocking Serrations on Slide ----------------------------------------------------------------------- 1.0 – 1.5
Cut slide for Bo Mar, w/o Sight
Plain cut --------------------------------------------------------------------------------------------------------------- 1.75
w/Slide Shields ------------------------------------------------------------------------------------------------------- 2.0
Cut slide for Dovetail Front Sight, w/o sights -------------------------------------------------------------- 0.5
Cut Slide for Novak Rear, w/o sight --------------------------------------------------------------------------- 1.0
Install Stake-on Front, w/o sight ------------------------------------------------------------------------------- 0.75
Flatten slide Top & Serrate, w/o sight ------------------------------------------------------------------------- 2.0
Dehorn & Break Edges for Carry (Does not include refinishing) ------------------------------------------ 1.0 – 2.5
Full Melt Down Beveling ------------------------------------------------------------------------------------------ 1.5 – 2.75
Modify 1911 Auto Frame for Beavertail Safety
Includes Fitting of Safety, does NOT include cost of Safety or refinishing --------------------------------- 1.5 – 2.5
Fit Grip Safety – No Frame Cut ---------------------------------------------------------------------------------- 0.5
Undercut Trigger Guard/Frame Junction --------------------------------------------------------------------- 1.0
Square Trigger Guard ---------------------------------------------------------------------------------------------- 2.0
Checker Front of Trigger Guard --------------------------------------------------------------------------------- 1.5
Fit Thumb Safety ---------------------------------------------------------------------------------------------------- 0.5 – 0.75
Install Ambidextrous Safety (Does Not Include Parts) ----------------------------------------------------- 0.75 – 1.0
Adjust or Install Magazine Catch ------------------------------------------------------------------------------- 0.5
Adjust Magazine Feed Lips -------------------------------------------------------------------------------------- 0.25
Install Fiber Optic Front Sight (Does not Include the cost of the sight) --------------------------------- 1.5
Install Auto Pistol Compensator
(Includes machine frame contour, thread barrel, index and line ream. No Refinishing Included!) --- 5.0
Checker Front Strap
18 LPI ------------------------------------------------------------------------------------------------------------------- 3.5
24 LPI ------------------------------------------------------------------------------------------------------------------- 4.0
30 LPI ------------------------------------------------------------------------------------------------------------------- 4.5
Serrate Rear of Slide ----------------------------------------------------------------------------------------------- 1.0
Glock Auto Pistols
Fit Aftermarket Barrel (Does not include barrel) -------------------------------------------------------------- 0.5
Install Manual Safety Kit (Does not include parts kit) ------------------------------------------------------- 0.75
Retro Fit Sights ------------------------------------------------------------------------------------------------------ 0.5
Trigger Job ------------------------------------------------------------------------------------------------------------ 0.5
Springfield XD
Fit Aftermarket Barrel (Does not include barrel) -------------------------------------------------------------- 0.75
Install Sights (Does not include sights) ------------------------------------------------------------------------- 0.5
Browning Hi-Power
Install Cylinder & Slide Sear Lever (does not include parts) ---------------------------------------------- 1.0 – 1.5
Install Cylinder & slide Hammer (does not include parts) -------------------------------------------------- 1.0
Install Spring Kit (does not include parts) ---------------------------------------------------------------------- 0.75
Trigger Job ------------------------------------------------------------------------------------------------------------ 2.0
Stock Work
Wood Finishing (Does not include any shaping or removing old finish)
Hunter Finish---------------------------------------------------------------------------------------------------------- 8.0
Unfilled Oil or Lacquer Finish on Average Stock ---------------------------------------------------------------- 8.0
Same finish but on Complicated Stock --------------------------------------------------------------------------- 11.0
Gunsmith finish ------------------------------------------------------------------------------------------------------- 12.0
Filled, rubbed oil finish on average stock ----------------------------------------------------------------------- 12.0
Same Finish but on Complicated Stock ------------------------------------------------------------------------- 15.0
Spray finish ------------------------------------------------------------------------------------------------------------ 6.0
Lacquer or Polyurethane -------------------------------------------------------------------------------------------- 8.0
Recutting Checkering (Other than by the hour, per panel)
Simple Pattern, i.e. Weatherby ------------------------------------------------------------------------------------ 4.0
Complicated Pattern, i.e. Fleur de Lis ---------------------------------------------------------------------------- 6.0
Glass Bedding Barrel and Action
Hunting Rifle ---------------------------------------------------------------------------------------------------------- 2.75 - 4.0
Match Rifles, M-1 Grand, M1A, etc. ------------------------------------------------------------------------------ 4.0
Pillar Bed
Remmington, Shilen, Savage type Tublar Receiver ---------------------------------------------------------- 3.0
Mauser, Pre-64 Winchester, Mod 70, flat bottom receiver -------------------------------------------------- 3.5
Install Recoil Pad (Labor Only) --------------------------------------------------------------------------------- 1.0
Install Adjustable Butt Plate (Labor only) ------------------------------------------------------------------- 1.5
Install Sling Swivels – std and Q/D --------------------------------------------------------------------------- 0.5
Install Stock Cross Bolt (not including finish) ------------------------------------------------------------ 0.75
Install Recoil Reducer
Simple Installation in Butt Stock ----------------------------------------------------------------------------------- 0.5
Hydraulic butt plate-style (Gra-Coil or Counter Coil) ---------------------------------------------------------- 1.0
Drill Stock & Install Recoil Reducer ------------------------------------------------------------------------------- 1.0
Inletting and Finishing of Semi-Finished Stock
Does not include checkering, recoil pad, special butt plate, grip cap, or other attachments ---------- 20.0
Free Float Barrel ----------------------------------------------------------------------------------------------------- 1.0
Fit, Bed and Finish Fiberglass Stock Blank ----------------------------------------------------------------- 6.0
Prefinished Synthetic Stock (fit and install barreled action) ----------------------------------------------- 2.0
Camo Painting Stock ----------------------------------------------------------------------------------------------- 3.0
Install Adjustable Comb Hardware (includes refinishing cut area only, no parts included) ---------- 2.5
Repair Broken Wrist – Pin and Epoxy (does not include recut checkering) ---------------------------- 2.0
Repair Broken Wrist – Pin and Epoxy (includes recut affected checkering) --------------------------- 4.0
Checkering
Custom Patterns – Hourly Rate ($75.00 hr.)
Standard Patterns
Pistol Grip -------------------------------------------------------------------------------------------------------------- 6.0
Fore-end --------------------------------------------------------------------------------------------------------------- 6.0
Complex Patterns
Pistol Grip -------------------------------------------------------------------------------------------------------------- 8.0
Fore-end --------------------------------------------------------------------------------------------------------------- 8.0
General Barrel, Action & Rifle Work
Check Headspace ---------------------------------------------------------------------------------------------------- 0.25 - 0.75
Make Chamber Cast ------------------------------------------------------------------------------------------------- 0.5 – 1.0
Remove Stuck Fired Case from Chamber (Very Stubborn (pull barrel and ream, bill @ shop rate) - 0.5 – 1.0
Remove Live Round from Chamber ------------------------------------------------------------------------------ 2.0 – 4.0
Remove Obstruction from the Bore (per item) ------------------------------------------------------------------ 0.5 – 1.0
Remove fouling from the Bore ------------------------------------------------------------------------------------- 0.5 – 1.5
Lap Barrel -------------------------------------------------------------------------------------------------------------- 0.5 – 3.0
Install Barrel Liner (less cost of liner and bluing) --------------------------------------------------------------- 2.0 – 3.0
Cut and Crown Barrel ---------------------------------------------------------------------------------------------- 1.0 – 2.0
Chamber and Fit Barrel to Action (Does not include cost of barrel, action, polishing or bluing)--------2.0 – 3.0
Install Pre-Threaded and Chambered Barrel
(not including Polishing & Bluing and Chamber is not Oversized) ------------------------------------------ 1.0 - 2.0
Lap in Bolt Lugs (not including setting back barrel or fitting new barrel) ----------------------------------- 0.5 – 1.0
Weld on New Bolt Handle ------------------------------------------------------------------------------------------- 2.25 – 3.0
Forging New Bolt Handle ------------------------------------------------------------------------------------------- 1.5 – 2.0
Make and Install Coil Spring --------------------------------------------------------------------------------------- 0.25 – 1.0
Make and Install V Spring ------------------------------------------------------------------------------------------- 1.5 – 4.0
Install Safety
Dakota, Gentry, Mod 70 Type Safety with Shroud (+ finishing) ---------------------------------------------- 2.0 – 3.0
Mark II Beuhler type -------------------------------------------------------------------------------------------------- 0.75 – 1.0
Chapman Swing Safety Lever -------------------------------------------------------------------------------------- 1.5 – 3.0
Trigger Installation or Adjustment
Shilen, Tmney, Dayton-Traister, Moyer Type -------------------------------------------------------------------- 1.0
If Clean and Fit Internal Parts --------------------------------------------------------------------------------------- 2.0
Winchester Mod 70 --------------------------------------------------------------------------------------------------- 1.0
Jewell -------------------------------------------------------------------------------------------------------------------- 0.5
Double Set – Pin/Weld ----------------------------------------------------------------------------------------------- 2.0 – 4.0
Single Set – Pin/Weld ------------------------------------------------------------------------------------------------ 2.0 – 4.0
Install Muzzle Brake – Non-Indexed/Index ---------------------------------------------------------------------- 1.0 – 2.0
If Barrel is Pulled Add ------------------------------------------------------------------------------------------------ 0.5
Re-contour Front or Rear Receiver Ring ------------------------------------------------------------------------ 1.0 – 2.0
Install Barrel Band Swivel – Clamp/Sweat-on ------------------------------------------------------------------- 0.5 – 2.0
Weld-up and Checker Mauser Stop Bolt ------------------------------------------------------------------------- 1.5
Checker Bolt Knob on Flat ------------------------------------------------------------------------------------------ 0.5
Checker Bolt Knob Circle or Band --------------------------------------------------------------------------------- 1.5 – 2.0
Re-barrel (Does not include finishing) ---------------------------------------------------------------------------- 2.0
Flute Barrel (Does not include finishing)-------------------------------------------------------------------------- 3.0
Flute Bolt (Does not include finishing) ---------------------------------------------------------------------------- 1.0
Blueprint Action (Bolt) ------------------------------------------------------------------------------------------------ 2.0
Fix Extractor ----------------------------------------------------------------------------------------------------------- 0.75
Open Bolt Face & Fit Extractor ------------------------------------------------------------------------------------ 0.75 - 1.5
Install & Fit Oversize
Firing Pin
------------------------------------------------------------------------------------ 0.5
Install Sako Style Extractor on Rem 700 ------------------------------------------------------------------------ 2.0
Replace Rem 700 Extractor ---------------------------------------------------------------------------------------- 0.25 – 0.5
Set Back Barrel & Recrown ---------------------------------------------------------------------------------------- 1.5
Silver Solder Rem Bolt Handle ------------------------------------------------------------------------------------- 1.5
Polish Chamber------------------------------------------------------------------------------------------------------- 0.25 – 0.5
Extend/Weld Magazine box on Mauser 98 ---------------------------------------------------------------------- 1.5
Weld-up/Re-drill Firing Pin hole in Bolt Face -------------------------------------------------------------------- 1.0 – 1.5
Fit Winchester Model 70 Safety ----------------------------------------------------------------------------------- 1.0
Install Receiver Sights
Gun already Drilled and Tapped – includes Collimation ------------------------------------------------------ 0.5
Gun Not Drilled and Tapped – (0.75 for each pair of holes) ------------------------------------------------- 1.25 – 2.0
. 22 Rimfire Rifles
Correct Feeding Problem ------------------------------------------------------------------------------------------ 1.0
Replace Firing Pin and Test Fire --------------------------------------------------------------------------------- 0.75
Correct Semi-Auto Headspace ----------------------------------------------------------------------------------- 1.0
Correct Headspace and Set Barrel Back ----------------------------------------------------------------------- 1.5
Remove Firing Pin Dent from Chamber ------------------------------------------------------------------------ 0.5
Straighten Magazine Tube ---------------------------------------------------------------------------------------- 1.0
Remove Dent from Inner or Outer Magazine Tube ---------------------------------------------------------- 0.5
Fix Trigger Problem and Harden if Necessary ---------------------------------------------------------------- 1.5
Fit Extractor ---------------------------------------------------------------------------------------------------------- 0.75
Dovetail Receiver for Tip-Off Rings ----------------------------------------------------------------------------- 1.0
Dovetail Front or Rear for Open Sights ------------------------------------------------------------------------ 0.5
Dovetail for Front & Rear sights with same Set-up ---------------------------------------------------------- 1.0
SHOTGUN WORK
Lengthen Forcing Cone
Non-Plated bores, per barrel ------------------------------------------------------------------------------------ 1.0
Plated Bores, per barrel ------------------------------------------------------------------------------------------ 1.5
Re-solder Rib (does not include bluing) ----------------------------------------------------------------------- 2.0
Re-solder Forend Lug (does not include bluing) ------------------------------------------------------------ 1.0
Epoxy Bed Stock, Pump/Semi-Auto ---------------------------------------------------------------------------- 1.0
Raise Dent in Barrel (does not include bluing) --------------------------------------------------------------- 0.75 – 1.75
Straighten/Adjust Barrel ------------------------------------------------------------------------------------------ 0.5 – 1.75
Polish Chamber/Bore ---------------------------------------------------------------------------------------------- 0.5 – 1.0
Back-Bore, per barrel, non-plated bores ---------------------------------------------------------------------- 1.0
Open/Modify Choke (per barel or tube, non-plated bores) ---------------------------------------------- 0.75
Per barrel, Chrome plated bores -------------------------------------------------------------------------------- 1.5
Install Screw-in Choke (Labor Only)
Win-Choke, Colonial, etc. / non-plated bores ---------------------------------------------------------------- 2.5
Port barrel, per barrel --------------------------------------------------------------------------------------------- 3.0
Trigger Job – Modular Fire Control System (Pump/Semi-Auto) ----------------------------------------- 1.0 – 1.5
Replace Firing Pin & Test Fire ---------------------------------------------------------------------------------- 1.0
Time Cartridge Stops – Pump/Semi-Auto -------------------------------------------------------------------- 0.75
Replace O-ring in Rem 1100 (plus cost of O-ring) ---------------------------------------------------------- 0.25
Correct Remington 1100 Feeding Problem ------------------------------------------------------------------ 1.0
Fit Receiver to Barrel Shoulder on Rem 1100 --------------------------------------------------------------- 0.5
Increase Ejector Throw in Browning A-5 --------------------------------------------------------------------- 0.75
Double Guns
Refitting Hinge Pin Lug (Easy Press Out) -------------------------------------------------------------------- 2.0
Engraved or Contoured to Receiver -------------------------------------------------------------------------- up to 8.0
Replace/Refit/Adjust Locking Block --------------------------------------------------------------------------- 1.0 – 2.5
Trigger/Sear Adjustment – Double (per side) --------------------------------------------------------------- 2.0
Repair/Replace In-Hammer Firing Pin (per Hammer) ---------------------------------------------------- 2.0 – 2.5
Repair/Replace In-Frame Firing Pin
Retaining System In-Tact and Removable ------------------------------------------------------------------ 1.0
Retaining System Not Intact or Removable ----------------------------------------------------------------- 4.0+
Tighten Locking System on In-Expensive Side x Side ---------------------------------------------------- 1.0
Headspace Correction on In-Expensive Pivot Barrels (per barrel)
(Weld underside of extractor) ---------------------------------------------------------------------------------- 1.25
Straighten/Adjust Barrel ---------------------------------------------------------------------------------------- 1.25 – 3.0
Install Mid/Front Bead
On rib -------------------------------------------------------------------------------------------------------------- 0.75
On Plain Barrel --------------------------------------------------------------------------------------------------- 1.0
SIGHT WORK
Sight-In Customer Gun (does not include ammo, targets, etc) ---------------------------------------- 0.5
Pattern Shotgun (does not include ammo, targets, etc) ------------------------------------------------- 0.5
Bore Sighting ---------------------------------------------------------------------------------------------------- 0.25
Drill & Tap Barrel/Receiver for Sights – First Hole ---------------------------------------------------- $50.00
Each Additional Hole -------------------------------------------------------------------------------------------- $25.00
Mauser 98 Receiver/Hardened Receivers (add up to .25 hr per hole)
Install Receiver Sights if Gun Already Drilled & Tapped (no wood cutting) -------------------------- 0.25
Cut and Refinish Wood ---------------------------------------------------------------------------------------- 1.0
Cut Dovetail in Barrel ------------------------------------------------------------------------------------------ 0.5
Install Front Sight Ramp
Sweat-on Type -------------------------------------------------------------------------------------------------- 1.0
Screw-on Type (including drill & tap) ----------------------------------------------------------------------- 1.0
Band Type ------------------------------------------------------------------------------------------------------- 1.0
Install Insert in Pistol Sight ------------------------------------------------------------------------------------ 1.0
Install Mid/Front Bead
On Rib ------------------------------------------------------------------------------------------------------------ 0.75
On Plain Barrel -------------------------------------------------------------------------------------------------- 1.0
Plug Hole and Re-drill for Bead ------------------------------------------------------------------------------ 1.0
Scope Mounting
Gun Already Drilled & Tapped -------------------------------------------------------------------------------- 0.5
Drill & Tap Barrel/Receiver for Sights – First Hole -------------------------------------------------------- $50.00
Each Additional Hole ------------------------------------------------------------------------------------------- $25.00
Mauser 98 Receiver/Hardened Receivers (add min. 0.25 hr. per hole)
Level Scope Base on Receiver (less cost of shims) ---------------------------------------------------- 0.5
Modify Base to Fit Receiver --------------------------------------------------------------------------------- up to 2.0
Lap Scope Rings ------------------------------------------------------------------------------------------------ 0.25 – 0.5